FCR Carb rubbers

Davw · Post by **Davw** » Wed Oct 28, 2009 5:23 pm

Have a set of 33mm FCR's but no matching carb rubbers - which seem to be like rocking horse toad. The original CV rubbers are too small - anyone solved this problem before??

Robbie · Post by **Robbie** » Wed Oct 28, 2009 5:38 pm

Yip give the fcr's to me

Davw · Post by **Davw** » Wed Oct 28, 2009 6:59 pm

Robbie wrote:Yip give the fcr's to me

Hey Robbie - why didnt I think of that - Simples

Got the list of race dates for Melville Club thorugh the door today - Roll on next season

luckyeddie · Post by **luckyeddie** » Wed Oct 28, 2009 7:40 pm

I got mine from cradley kawasaki about Â£35 a set

Davw · Post by **Davw** » Wed Oct 28, 2009 8:15 pm

luckyeddie wrote:I got mine from cradley kawasaki about Â£35 a set

Thanks for that - will call em tomorrow

Davw · Post by **Davw** » Thu Oct 29, 2009 10:20 pm

luckyeddie wrote:I got mine from cradley kawasaki about Â£35 a set

Inflation has set in - now Â£60 / set :smt013

luckyeddie · Post by **luckyeddie** » Fri Oct 30, 2009 8:28 pm

i only got mine 2 may be 3 months back a set for me and set for a mate
Â£8 odd each Â£35 per set .

Post by **jake** » Fri Oct 30, 2009 9:16 pm

I hope cradley havent started a new policy of random ripoffness as i still havent got over paying nearly 40 quid or whatever it was now for my front wheel bearings!

that said, i did need them.. and as usual they where on my doorstep the next day.

Ballsout Racing · Post by **Ballsout Racing** » Sat Oct 31, 2009 9:21 am

For bearings I usually go to bearing suppliers like these: http://simplybearings.co.uk/shop/ball_b ... 7Qod2mM29g

Â£40 is just a rip off!

My flatslides go into my CV rubbers, it's a bit of an effort, but they do go in

coley · Post by **coley** » Sun Nov 01, 2009 6:24 pm

Ballsout Racing wrote:For bearings I usually go to bearing suppliers like these: http://simplybearings.co.uk/shop/ball_b ... 7Qod2mM29g Â£40 is just a rip off!

My flatslides go into my CV rubbers, it's a bit of an effort, but they do go in

Lightly grease or oil the rubbers and they will go in, when you take the carbs back off the rubbers usually pull out of their housing though. (not a problem)

neil_cb125t · Post by **neil_cb125t** » Wed Nov 18, 2009 6:33 am

yeah very little mods required.. you can open them up a little but bit o rubber grease and its all god - lube is the key!!

CaNsA · Post by **CaNsA** » Wed Nov 18, 2009 6:37 am

There's always time for lubrication.....

Mori Man · Post by **Mori Man** » Thu Nov 19, 2009 1:36 am

Davw wrote:Have a set of 33mm FCR's but no matching carb rubbers - which seem to be like rocking horse toad. The original CV rubbers are too small - anyone solved this problem before??

Part # 16065-1241 x 4 = 3,696 Yen
Part # 92068-006 x 4 = 672 yen

About Â£30 for the inlet rubbers and the vacuum block off caps.

You do get 38 & 40mm inlet , 38 are OK for the CVK rubbers but I wouldn't be forcing the 40 in there as all you'll do is reduce the intake size.

MM!

www.zxrworld.co.uk

FCR Carb rubbers

FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers

Re: FCR Carb rubbers