Pulling to the right.
Moderator: Moderators
-
- zxr400 oc member
- Posts: 297
- Joined: Sat Oct 20, 2007 7:01 pm
- My Bike: zxr 400 h1
- Location: Cleethorpes
Pulling to the right.
Me again, more advice please. Just had puncture fixed. I rested the bike on it's forks when the wheel was off, raised up on slabs. I did this all very gently, and all went ok, put the old girl back together, all seemed well. Rode her and she pulls to the right and seems very twitchy around bends. All very upsetting as the other day I was king of the road.
Please advise?
p.s. tyre pressure is spot on.
Please advise?
p.s. tyre pressure is spot on.
Action is the antidote to despair.
- RedexRobB
- Site Admin
- Posts: 7212
- Joined: Fri Aug 30, 2002 7:37 pm
- My Bike: ZXR400L3
- Location: Ipswich, Suffolk
Re: Pulling to the right.
thats a weird one, didnt do the spindle up too tight did you?
- masterofinsanity
- Site Admin
- Posts: 8103
- Joined: Thu Aug 29, 2002 12:36 am
- My Bike: Aprilia Tuono Fighter
- Location: England
- Contact:
Re: Pulling to the right.
sounds like the brakes are binding on the right hand side.
Don't forget people there is more to the zxr400 than this forum... check out www.zxrworld.co.uk also.
-
- zxr400 oc member
- Posts: 297
- Joined: Sat Oct 20, 2007 7:01 pm
- My Bike: zxr 400 h1
- Location: Cleethorpes
Re: Pulling to the right.
They could both be right, I need to get a torque wrench.
Why would the brakes bind now when they weren't before?
Why would the brakes bind now when they weren't before?
Action is the antidote to despair.
-
- zxr400 oc member
- Posts: 297
- Joined: Sat Oct 20, 2007 7:01 pm
- My Bike: zxr 400 h1
- Location: Cleethorpes
Re: Pulling to the right.
p.s. If I have done the spindle too tight why would it do that and will it damage it permanantly?
Action is the antidote to despair.
- RedexRobB
- Site Admin
- Posts: 7212
- Joined: Fri Aug 30, 2002 7:37 pm
- My Bike: ZXR400L3
- Location: Ipswich, Suffolk
Re: Pulling to the right.
My reasoning was since thats probably the only thing you will have changed, apart from the tyre (and i assume thats been done properly), that may be the cause. As for why it does it i dont know i could be wrong, but worth checking all the same
Possible damage i believe it that the fork seals may get ruined, other than that i dont know.
Possible damage i believe it that the fork seals may get ruined, other than that i dont know.
-
- zxr400 oc member
- Posts: 297
- Joined: Sat Oct 20, 2007 7:01 pm
- My Bike: zxr 400 h1
- Location: Cleethorpes
Re: Pulling to the right.
I did loosen it and tighten not as much and it seems a little better, although it still feels a little funny. I think it may be a little psycholgical, due to a lack of confidence in my mechanical skills.
Action is the antidote to despair.
- jake
- zxr400 oc member
- Posts: 1016
- Joined: Mon Oct 02, 2006 10:03 pm
- My Bike: tomos moped
- Location: wirral
Re: Pulling to the right.
check the forks to see if one has slipped thru the yoke a little. make sure all yr pinch bolts are nice and tight-not to tight tho...
On my bike, sometimes if the speedo housing isnt in its right place, the wheel does'nt spin freely.
On my bike, sometimes if the speedo housing isnt in its right place, the wheel does'nt spin freely.
-
- zxr400 oc member
- Posts: 297
- Joined: Sat Oct 20, 2007 7:01 pm
- My Bike: zxr 400 h1
- Location: Cleethorpes
Re: Pulling to the right.
The speedo i think is ok, it's in the little slot anyway, although it looks different? My paranoia again!!!
Action is the antidote to despair.
- jake
- zxr400 oc member
- Posts: 1016
- Joined: Mon Oct 02, 2006 10:03 pm
- My Bike: tomos moped
- Location: wirral
Re: Pulling to the right.
dont get paranoid dude! just make yourself a brew, take the front wheel out again. spin the axle, if its nice, put wheel back in making sure evrythin is cool with the speedo drive( make sure it sits in between the 2 lugs) and spacer, tighten up. and eliminate that if its still doing it..
i had a problem with my speedo drive. i thougt it was in properly, but it used to spin around and stiffen up when i tightened the axle. They seem a bit hit and miss, cos it has'nt done it for a while..and my wheels are in and out very often.
i had a problem with my speedo drive. i thougt it was in properly, but it used to spin around and stiffen up when i tightened the axle. They seem a bit hit and miss, cos it has'nt done it for a while..and my wheels are in and out very often.
-
- zxr400 oc member
- Posts: 1918
- Joined: Fri Feb 23, 2007 10:34 am
- My Bike: kwack ZXR750L1
- Location: Northampton
Re: Pulling to the right.
did you put all the spacers back in AND in the correct places?
ZXR750 L1
tail tidy, polished bits, custom paint job, k&n, dynojet, Full akropovik, down geared, GSXR calipers, hel brake lines front and rear & clutch line, maxtron resprung froks 120BHP
BikePics page-
http://www.bikepics.com/members/zxr400rene/
tail tidy, polished bits, custom paint job, k&n, dynojet, Full akropovik, down geared, GSXR calipers, hel brake lines front and rear & clutch line, maxtron resprung froks 120BHP
BikePics page-
http://www.bikepics.com/members/zxr400rene/
-
- zxr400 oc member
- Posts: 297
- Joined: Sat Oct 20, 2007 7:01 pm
- My Bike: zxr 400 h1
- Location: Cleethorpes
Re: Pulling to the right.
There's only one spacer on the right hand side isn't there? The others just the speedo housing?
Action is the antidote to despair.
- jake
- zxr400 oc member
- Posts: 1016
- Joined: Mon Oct 02, 2006 10:03 pm
- My Bike: tomos moped
- Location: wirral
Re: Pulling to the right.
yep, thats right, just the one on the opposite side to the speedo. Any luck ?
-
- zxr400 oc member
- Posts: 297
- Joined: Sat Oct 20, 2007 7:01 pm
- My Bike: zxr 400 h1
- Location: Cleethorpes
Re: Pulling to the right.
Phew, not yet, thought I'd made a big mistake then. No luck yet, will take the calipers off tomorrow and then bleed them. Fingers crossed.
Thanks for all the advice though. Will get back to you all with results.
Thanks for all the advice though. Will get back to you all with results.
Action is the antidote to despair.
-
- Posts: 1
- Joined: Sat May 10, 2008 5:09 pm
Re: Pulling to the right.
hehehe, even if you totally removed one of the front calipers you won't be experiencing "pulling to one side"...it's a common misconception... taken from how a 4 wheeled vehicle behaves when there is a braking imbalance.
a single front tire has obviously only 1 axis/track... doesn't matter which side the braking force is applied... there's only one track/axis to brake. that's why smaller displacement bikes sometimes just has 1 disk brake upfront... not to mention all the bikes which have only one disc at the back.
what CAN cause "pulling" to one side are misalligned front-to-rear tires... travelling in a straight line do your tires create just one "track"?
a single front tire has obviously only 1 axis/track... doesn't matter which side the braking force is applied... there's only one track/axis to brake. that's why smaller displacement bikes sometimes just has 1 disk brake upfront... not to mention all the bikes which have only one disc at the back.
what CAN cause "pulling" to one side are misalligned front-to-rear tires... travelling in a straight line do your tires create just one "track"?